Knowing Plumbing Basics is Important For Installing a Bathtub
Knowing Plumbing Basics is Important For Installing a Bathtub
Blog Article
Right here below you can find additional reliable help and advice relating to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately difficult job. If the old tub is readily available, the project can relocate easily; if you have to open a wall to remove the old bathtub and place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a house handyman's skills, although you will require a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually certified on your own for the work as well as are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed job, it is far better to think about using one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This article will certainly assist you install a brand-new bathtub in your washroom if you have already gotten a brand-new bathtub and do not require to change the plan of your previous water supply pipelines.
Your devices as well as product list must comprise the following:
Preparing for the Installation
First of all, the supporting structure provided with the bathroom must be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing taps can be quite troublesome because of the restricted gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Before moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, put the bathtub in the called for position. The wood boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub up until the level checks out degree.
To mount faucets, fit the bottom of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Activate the water supply and also examine all joints and brand-new pipework for leakages and also tighten them if required. Load the bath tub as well as additionally examine the overflow outlet and also the regular outlet for leaks.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub ought to wait up until the bath tub has been made use of at the very least when as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making sure that the washing machines are in place between the tap and also the sink. Secure the tap in position with the manufacturer provided backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The previous kind should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to fracture a stiff seal, causing the water to permeate the wall surface between the bath and also the tiling, causing issues with dampness and feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and installations. They are sold in tubes and cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the tub with water prior to securing, to permit the movement experienced when the tub remains in use. The sealant can crack relatively early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the market. It is suggested to fit the ceramic tiles using water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting on Tools You Need to Install a New Bathtub while doing a search on the search engines. Sharing is caring. Helping people is fun. Thanks for your time. Visit again soon.
Immediate support available. Report this page